How To Put Headboard On Dorm Bed

One detail that helped brand my room feel more than like home was adding a headboard to my bed frame. Instead of simply a mattress and decorative pillows sitting against a wall, the headboard made information technology look much more like a bed and completed the await.

While there are enough of options out there to purchase a headboard, I decided to make my own. And much to my surprise, information technology was relatively like shooting fish in a barrel! While it definitely takes some fourth dimension, this was a corking summer project to work on prior to heading to school.

My mom and I watched several videos on the best fashion to assemble a DIY headboard. Nosotros incorporated techniques from a diverseness of suggestions. I was so happy with the final production and was thrilled information technology stayed together the whole year. If you choose to make your ain headboard too, below I've shared a step-past-footstep guide for building my headboard.

For my headboard, I used two layers of heavy paper-thin from a furniture box. Looking back, I would recommend using a half inch piece of plywood instead as it would concord staples improve. I chose the paper-thin to reduce the weight for transporting it to schoolhouse. However, the cardboard did not hold the staples as well equally plywood, and the wood would make the assembly process easier. I also glued 2 yardsticks vertically to the back to give it extra support due to its height.

My headboard was 40 inches broad and 43 inches alpine. In that location were a few elements I kept in mind when deciding on the dimensions of my headboard. First, I looked up the measurements for the bedframe of my dorm bed. I wanted it to be every bit wide every bit my bed and knew it would sit on the bedframe backside my mattress. I too wanted it to exist tall enough that my monogram would sit above my pillows. I then needed to consider its size to exist sure it fit in the back of my car for transporting to school. At each stage of construction, I placed it in the car to check its size.

While some headboards are clean rectangles, I knew I wanted to add together a footling more shape to mine. So, I decided to add the cut outs on the top corners. I measured to draw 3 inches off of the top and side corners. I used a basin to trace the same shape on each side and create a smooth edge. When I cut the entire shape of the headboard out of the cardboard, I made lilliputian tweaks on these corners to make them as symmetrical as possible. It's important to have a good shape here, but don't spend too much fourth dimension on perfecting the edges – it will be covered with the padding and loses some of the shine edge.

I wanted to be able to lean upwards against my headboard and for it to be comfy. So, I chose to cover my headboard with padding. Foam padding sold at the fabric store is expensive. I purchased a less expensive mattress pad for a California Male monarch mattress and cutting the foam mattress topper into two pieces. I placed the apartment side of i slice of the topper on the cardboard and stapled it with a staple gun to the paper-thin. Then I placed the 2nd slice of the mattress topper apartment side out and stapled it to the cardboard. I wrapped both pieces of foam effectually the back and stretched and stapled information technology down.

Information technology's important the foam is wrapped equally tightly as possible and so that it is polish on the front. I highly recommend laying the foam padding on the ground, placing the cardboard on top and lining the cardboard upwards and so that yous can ensure the padding will wrap around symmetrically. This step requires a lot of staples, but it's of import that this layer sticks prior to adding whatsoever fabric on top of information technology. I may have added more than necessary, merely I never had whatever bug with the padding coming apart, and so it paid off in the long run!

In the online tutorials that I reviewed, others did not wrap the foam effectually to the back and instead added a layer of batting to create rounded edges. This would have provided more definition to the curves, but I personally liked the additional thickness that the foam provided.

3. Cover the padding with textile.

I then placed cloth over the cream. I purchased duck cloth from the upholstery section of the fabric store. This was a heavier textile that could stand up up to day-to-solar day wear. I wanted to add together a lilliputian personalization to my headboard, so prior to assembling the headboard I had the textile monogrammed. I went to a local commercial embroidery company because the size of the monogram was x inches.

It is important to have two people for this part. One person should be in charge of lining upward the textile and holding it in place, while the other staples the fabric to the back of the board. I advisedly lined up the monogram, held the board upright and put in a few staples to concord the textile in place. And so I turned the lath over (facing downwardly) to fully secure the fabric. My mom pulled the cloth very tight while keeping information technology lined up and I stapled the fabric in identify on the dorsum. If I idea I had used a lot of staples in the previous step, this one required even more. I wanted to make sure the assembly would not come up apart in transporting information technology to Tuscaloosa or fifty-fifty afterward I had moved in to my room. Once I had the front textile secure, I glued a few pieces of scrap fabric to comprehend the back, making sure none of the staples remained visible.

4. Become ready to ship.

In one case I finished the headboard, I covered it in plastic furniture wrap so that it would not get dirty when I was moving it into my dorm. This also helped forbid anything from scratching or cutting the fabric during the moving process!

I loved how information technology turned out. It provided a pop of color confronting the biscuit walls, and the double layer of foam provided plenty of cushion, making it soft to lean confronting when I studied or sat up in bed.

Are you making your ain headboard for your dorm? Have y'all made a headboard in the past and have any recommendations? I'd love to hear!

P.S. Please don't hesitate to reach out if you lot accept any questions, I'd be more than happy to help!

Source: https://www.letsgetpreppy.com/2018/06/freshman-15-diy-dorm-headboard.html

Share this post